Everbuild Tecnic Puraflex 40 High Modulus PU Sealant and Adhesive, White, 300 ml

Product Information

Water - visibly dripping through into your cabin during rainy days. Leaking water can often be seen forming small droplets on the bottom of protruding bolt heads. Wait for a forecast of rain or cheat and use a hose to find leaks. If you get your bilge bone dry beforehand, you'll be able to follow the trails of water from any leaky hardware by looking at your bilge areas with a hand torch. This method works amazingly well. If you have a dirty bilge it seems to be even easier and the trail seems to show up clearer where the dirt is wet.

is all around one part polyurethane adhesive sealant that can be used to bond wood, gel coat and fibreglass. It can also be used above and below the waterline.

Everbuild Tecnic Puraflex 40 300ml

Everbuild Stix-All is a one component adhesive sealant utilising the best elements of silicone and polyurethane technologies to create a hybrid. It hasn't been designed for marine use specifically but It is compatible for adhering with most the common materials and can be applied on both damp and wet surfaces. It will bond to metals, plastics, glass, concrete, plasterboard, plaster, polyester, perspex, glass, wood, enamel, painted surfaces and GRP.

Tensile Strength - the resistance of a material to breaking under tension. To put it even clearer this is the amount of force a material can take until it breaks apart. This is measured in N/mm2 to MPa and can normally be found on a product datasheet. You need good mechanical adehsion with flex. Look at the datasheet for Sikaflex 291i. You don’t want to use the 3M products as the hose at some point will need replacing. Resistant to fresh water, seawater, limewater, sewage effluent, diluted acids and caustic solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils. Greg - I have a Meridian 391 2010 the front windows are leaking a little bit and is dripping in the master state room on the bed. I have tried to fill the area where the window sits on the lower side with silicon to achieve a water seal. Does not work. Pulled out all the silicon and I am going to try to fill and seal with Butyl or polyurethane. which would you recommend?Before application, please ensure all surfaces are clean, dry and dust-free before using Everbuild Puraflex 40. All old sealant and mastic joints should be removed before application. In addition to that, when using on glass, metal and aluminium, areas should be cleaned using a solvent cleaner before application for optimum adhesion. When using with solvents, always ensure adequate ventilation. Avoid heat, sparks and open flames. Observe and follow all precautions listed on the solvent container label. It is not recommended for application to surfaces that are below 5˚C as it is impossible to guarantee a dry, frost-free surface at these temperatures. Therefore the sealant will most likely fail. It is unlikely that priming will be required; however, concrete must be sealed using a Primer. After that, if you are in doubt, consult Technical Services.

Sealants were originally designed to patch holes in planes during the war but since then they've got a lot more complicated. Corporate competition means companies are continuously trying to outdo each other. The marine industry is constantly screaming out for products that last longer and perform better and subsequently, we are fed increasingly better sealants. A lot of companies who create sealants eventually wise up to the fact that their product will work in the 'marine' industry, and often subtly add it to their datasheet without it being a specific marine product and liable for leisure tax. My first thought , what’s caused the corrosion in the first place, do the anodes need replacing and are there earthing issues with the leg. Compatibility - will it work with your material you wish to bond it too? Will it be safe for below the waterline? It is said that silicone is an inert synthetic polymer compound and is technically part of the rubber family. You can imagine why its been a favourite in boat maintenance for some time. Its UV resistant, heat resistant, a great insulator and is ideal for creating gaskets. Its downfall is that it makes for a weak adhesive and for this reason sometimes is unpractical for use below the water line.

Stocks we install and supply

Serviceability - how easily will I be able to remove and replace the sealant, how long does it take to set?

Hi Rich, If you are using aluminium frames then essentially the sealant will only need to be used to create a gasket. There is my opinion is no need to have a good adhesion if the window is held tight by rivets or bolts and a frame. Aquaseal mSEAL has been known to work well for this purpose and Geocel Marine Rubber Silicone is something I have personally used with good results. If you’re bonding rubber to a painted surface then I’d personally i’d use emery paper to remove the paint then your bonding, rubber to aluminium only. My memory of the MSDS data is that OB1 was essentially the same as CT1 apart from an additional component. I can't remember what it was but did write that I thought it likely to enhance cross-linking to either speed up setting time or strength of the material, probably both (by promoting formation of urethane links). A favourite amongst boating enthusiasts CT1 is suitable as a universal adhesive and will work in all applications. CT1 has no shrinkage and can be applied in both damp and wet conditions. It adheres to most metals (including lead) as well as glass, mirrors, wood, polystyrene and GRP.

Solseal Delivery Schedule

We've even created a beautiful acronym for you to remember: 'SFCSS' (pronounced; Suu-Fuu-Cissss). See, if that's not catchy enough for you then I don't know what is! Terms Explained A non-adhesive sealant will generally rely on the aid of a fitting, screw or bolt to create a waterproof seal. With a normal sealant, you are essentially creating a waterproof gasket. You can't rely on normal sealant to hold anything in place; you are relying on a method of fastening, for example; a screw or bolt. Types Of Sealant There were posts about the "similarity" with CT1 and that it was actually an improved formulation. Also a threat of legal action plus mention in advertising that the OB1 formulation had been in use for over 15 years and made by a private company. I could not find details of the manufacturer and it almost seemed to be a big secret. It appeared reasonable to assume that some sort of legally binding agreement had been signed regarding direct competition or comparison with CT1 by name (could be wrong). UniBond FlexTec FT101 is a one component hybrid polymer which can be used to seal, fill and bond. It claims to be able to bond without the use of a primer to a wide range of materials but doesn't specify which ones it does not. It can also be applied on both damp and wet surfaces but does take 24hours to set and may not ideal for fast same day repairs. Remove all of the sealant taking care not to damage the glass or frames, using a sharp knife. Tape the window and frames up using frog tape or blue painters tape then apply the sealant in even smooth beads.